Standards
The list below contains standards that govern one or more areas of metrology. This is not an exhaustive list. If there is a standard that you feel belongs in this list, please email info@emetrology.com.
-
ASTM B946-11 Standard Test Method for Surface Finish of Powder Metallurgy (P/M) Products
Scope 1.1 This test method covers measuring the surface finish of powder metallurgy (PM) products at all stages of manufacturing from green compact to fully hardened finished component. 1.2 This test method provides the definition and schematic of some common surface finish parameters (Ra, Rt, and Rz ISO) 1.3 The values stated in inch-pound units are to be… -
ASTM D4417-21 Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
Scope 1.1 These test methods cover the description of techniques for measuring the profile of abrasive blast cleaned surfaces in the field, shop, and laboratory. There are other techniques suitable for laboratory use not covered by these test methods. 1.2 Method B may also be appropriate to the measurement of profile produced by using power tools…. -
ASTM F1048-87, Standard Test Method for Measuring the Effective Surface Roughness of Optical Components by Total Integrated Scattering
Scope This standard was transferred to SEMI (www.semi.org) May 2003 1.1 This test method covers the measurement of the effective surface roughness of an opaque reflecting surface as determined by the total integrated light scattering (TIS). -
ASTM F2033-05: Standard Specification of Total Hip Joint Prosthesis and Hip Endoprosthesis Bearing Surfaces
This specification covers the sphericity, surface finish requirements, and dimensional tolerances for hip joint prostheses and hip endoprostheses. -
ASTM F37: Standard Test Methods for Sealability of Gasket Materials
These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials. These test methods are suitable for evaluating the sealing characteristics of a gasket material under different compressive flange loads. -
ISO 12085:1996 – GPS — Surface texture: Profile method — Motif parameters
Scope This International Standard defines terms and parameters used for determining surface texture by the motif method. It also describes the corresponding ideal operator and measuring conditions. -
ISO 12179:2021 – GPS — Surface texture: Profile method — Calibration of contact (stylus) instruments
Scope This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 3274. The calibration and adjustment is intended to be carried out with the aid of measurement standards. Annex B specifies the calibration and adjustment of metrological… -
ISO 13565-1:1996 – GPS — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions
Scope This part of ISO 13565 describes a filtering method for use with surfaces that have deep valleys below a more finely finished plateau with a relatively small amount of waviness. The reference line resulting from filtering according to ISO 11562 for such surfaces is undesirably influenced by the presence of the valleys. The filtering approach described in this standard… -
ISO 13565-1:1996/Cor 1:1998 – GPS — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions — Technical Corrigendum 1
Technical Corrigendum 1 to International Standard ISO 13565-1:1996 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. Page 1 Clause 2 Replace “ISO 4287:1996” with “ISO 4287:1997“.”ISO 4287:1997” Page 4 Figure A.1 Replace “Datum planes” with “Datums”. -
ISO 14978: 2006 Geometrical Product Specifications (GPS) — General Concepts and Requirements for GPS Measuring Equipment
Scope This document specifies the general requirements, calibration, terms and definitions of characteristics of GPS measuring equipment, for example micrometers, callipers, gauge blocks and rotary axis form measuring instruments. This document forms the basis for standards defining and describing the design characteristics and metrological characteristics for measuring equipment and gives guidance for the development and…
1-12 of 60 results
No results found. Try a different combination of filters.